The Faux Round Swatch

By Tabetha Hedrick

Most of us love a good circular, seamless project, and the very idea of socks, hats, top-down raglans or circular yokes brings us a joy that is virtually palpable. Well, except the little gauge swatching part (because we ALL do our gauge swatch, right?!). This area can cause some angst for knitters, but I’m going to show you my favorite method of swatching—The Faux Round Swatch!

The reason we need to swatch in the round, versus attempting a flat swatch for a circular piece, is that flat stockinette stitch is looser (thanks to those pesky WS purl stitches), resulting in few stitches per inch. Circular stockinette stitch is tighter (because we aren’t purling), resulting in more stitches per inch. The point is: A flat swatch for a circular project is a no-no.

The first method I leaned to swatch in the round was simply casting on double the number of stitches, working in the round on double-point needles (dpns) and then binding off. Lay it as flat as you can, in half, and try to count your stitches on the cushioned surface (created by the other half underneath). Not exactly accurate, is it? It also uses a lot of yarn and takes more time to work.

And here comes the Faux Round Swatch! It can take a little bit of practice to get into the groove, but it uses less yarn, takes less time and just looks cool with a fringe effect. Without further ado, here’s how you go about it!

Tools:

  • Circular needle or dpns used for the project
  • Yarn for the project
  • Gauge for the project (i.e.: X sts and X rows = 4 inches/10cm in Stockinette Stitch)

Step 1. Take the number of stitches in the gauge and add 6 stitches to that number. Cast on that amount of stitches onto your needle. For example, if gauge is 20 stitches = 4 inches, you’ll add 6 to that to cast on 26 stitches.

Step 2

Step 2

Step 2. K1, p2, work your gauge stitch pattern, p2, k1.

Step 3

Step 3

Step 3. Instead of turning your needle to work the WS, push your stitches back to the other end of the needle (a). Take the working yarn and, keeping it at the back of the swatch, wrap it 2-3 times around your finger (b), keeping it snug, and begin working across the stitches as indicated in Step 2 (c). Let go of the loop you’ve created after the first 2 or 3 stitches (d). When you get to the end, pull the strands snug again.

How it looks

Here’s how it looks

This process creates loops across the back of the swatch, slightly curling the edges (a, b, c). The first and last stitches will also look sloppy (d), but don’t let that bother you. That’s why we added those “buffer” purl stitches to the edges.

Repeat Step 3 until you have worked the number of rows indicated for 4 inches in the gauge information. (If the gauge said 32 rows = 4 inches in stockinette stitch, you work 32 rows.)

Step 4. After working all desired rows, turn your work (no loop this time), so the WS is facing you, and bind off in pattern.

Step 5

Step 5

Step 5. Grab your trusty scissors, spread out your swatch and snip the loops right in half so they fall away and flatten your edges again (a, b, c). If you are a perfectionist like me, loose edges simply won’t do. So, just pinch the stitch and pull each loop-strand tightly (d). If you are going to machine-wash your swatch, go ahead and tie every 2 strands together in a little knot for security.

Step 6

Step 6

Step 6. Block your swatch as desired.

Step 7

Step 7

Step 7. Measure your swatch. With a ruler and the WS of your swatch facing, measure JUST the gauge swatch part between the buffer stitches. Here are my gauge rules:

  1. If it is 4 inches in width and 4 inches long, you are good to go.
  2. If it is smaller than 4 inches by less than 1/4 inch, go up 1 needle size. If it is smaller than 4 inches by more than 1/4 inch, re-swatch with 1 or 2 needle sizes larger.
  3. If it is larger than 4 inches by less than 1/4 inch, go down 1 needle size. If it is larger than 4 inches by more than 1/4 inch, re-swatch with 1 or 2 needle sizes smaller.

I hope this tutorial for the Faux Gauge Swatch makes your circular knitting days a little more joyful!

Tabetha HedrickTabetha lives by the belief that joy comes when fully participating in the present moment, especially when it comes to fiber. Surrounding herself with yarn through knitting, designing, spinning and teaching ensures that blissful continuity. For patterns and class schedule, visit her website at www.tabethahedrick.com.

7 Responses to The Faux Round Swatch

  1. Alice says:

    This is genius! Can’t wait to try it with my next circular project.

  2. Anny says:

    BRILLIANT! Thank you sooo much! I am not a big fan of swatching at the best of times, but when it comes to doing it for a project in the round I’m tempted to change projects rather than do the swatch, so this will be so incredibly useful. I’ll have to give it a go.

  3. Suzanne Novoselac says:

    This is great! I had been wondering how to do this, and it looks very easy. Thank you so much for posting it.

  4. Timaree J Cheney says:

    Good idea! I hate swatching because it uses up some of my precious yarn and I really don’t want to have to buy an extra skein just so I can use it for swatching . Yarn is expensive!

    An extra problem is changing your knitting tension as you work. I had one pattern suggest you just start with a sleeve where you could correct it as you go. We’ll, swatching it or not, my sleeves came out two seriously different sizes! How does swatching help with that or what will? That sweater has been sitting unfinished for 10 years now.

  5. Penne Rosenthal says:

    Thank you for sharing this technique as doing the swatch for circular knitting has always been a problem for me. However, I do not understand how this works and why the gauge would be different from a flat knitted swatch. Could you possibly explain why this works? Thank you! Even if it only works in my imagination, it is a relief to have something that is easy and fast.

  6. Elaine says:

    Absolute genius. You made my day.

Leave a Reply

Your email address will not be published. Required fields are marked *


*

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>